When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.
Sword specification:
Condition: Brand New
Blade Material:Clay Tempered T10 Steel
Handle Material:Genuine Ray Skin + Hardwooden
Saya Material: Hardwooden
Fitting Material :Iron、Alloy、Brass
Size：Overall Length: 41 inch/103cm，Nagasa Length: 28.7 inch/73 cm，Handle Length: 10.6 inch/27 cm，Blade Width(near Habaki)： 1.26 inch / 3.2cm，Blade Width(near Kissaki) ：0.91inch / 2.3cmBlade:
The Blade Of The Sword Has Been Hand Forged Using The Ancient Method Of Sword Making . Full Hand Forged And Full Hand Polished，Shinogidukuristructure blade.
The Blade Was Made Of T-10 High Carbon Steel, And It Has Been Laminated In A Maru Configuration(Single Type Mono Steel). Differential Hardened And Clay Tempered, Water Quenched And Polished.
The T-10 High Carbon Steel (The Steel Has A 0.1% Carbon Content And 0.4% Manganese.）Is Very Solid And Holds An Edge Well. This Blade Was Then Clay Tempered And Has More Than 14 Process Hand Sharpening Work. Which Made The Surface Of The Blade Like A Mirror.
This Blade Has Been Tried And Tested To Cut Everything That Gets In Its Way. The Sori (Blade Curvature) Is Specially Crafted To Create Leverage In Order To Perform The Smoothest And Cleanest Cuts. That In Combination With The Choice Of Traditional And Our Top Selling Koshirae (Fittings), Assures That You Will Get The Best Of Both Appearance And Functionality.
The Japanese Hamon Pattern Is Done In The Same Process As The Traditional Method. Harden The Edge Is By Using The Special Clay Wrapping The Blade Then Put In Water To Quench. It Requires A Lot Of Skills. The Fire Temperature Can Not Be Too High Or Too Low It Needs To Be Well Controlled By The Sword Smith. The Blade Is Then Put Into Water For Quenching. The Blade Shape Is Done This Process Creates Beautiful Hamon Hada And Martensite (Grains) On The Blade Surface. Clay To Protect The Edge And Quenched In Water To Temper The Mune Or Spine Of The Sword. The Hardness Of The Carbon Steel Measures At An Impressive HRC On The Rockwell Scale. The Perfect Combination Of The Hardness Of The Edge Steel, And The Increased Sori (Curvature Of The Blade), Enables This High Quality Blade To Easily Cut Through Tatami Straw Mats Or Bamboo For Tameshigiri.Fitting:
This Tsuka is wooden one wrapped with genuine ray skin, and with silk ITO in the traditional wrap.
The Fuchi and Kashira on the tsuka are made of Ironwith matching Menuki on each side as an ornament, Two Mekugis(peg) are nailed to secure the Tasng of the sword. (Sword can be disassembled by picking up the Two Mekusgis (peg).
This saya (sheath) of the sword is hard wooden, and lacquered superior paint to highly gloss the surface of it. The Sage-O is tied around the Kurikaka (knob) of the saya, the Koiguchi (scabbard mouth) and Kojiri (scabbard tip) has been hardened.NOTE::
1.A silk sword bag comes with the sword. but the wooden stand in below item pictures is NOT included.
2.Please do not store in a humid environment. When the sword is not in use, please keep the blade clean to ensure that there is no water stains, then wipe a layer of maintenance oil to prevent rust. If there is no special oil, use gasoline engine oil.
3.Due to our swords are full hand made,each one is unique，so Specs will vary slightly from sword to sword，There may be slight differences in their size，please refer to the actual received andunderstand.
ABOUT 
